Hallo,
brauche Hilfe dabei bei dem Nintendo DS Emulator - desmume auf deutsch zu konfigurieren.
Mir fehlt anscheinend das richtige Modul.
Ich weiß nicht welches ich aus der List wählen soll.
Das sind alle Optionen die mir "--help" anzeigt.
Code
@linux-xiir:~> desmume --help-all
Aufruf:
desmume [OPTION …]
Hilfeoptionen:
-h, --help Hilfeoptionen anzeigen
--help-all Alle Hilfeoptionen anzeigen
--help-gtk GTK+-Optionen anzeigen
GTK+-Optionen
--class=KLASSE Programmklasse, die vom Fenstermanager benutzt wird
--name=NAME Programmname, der vom Fenstermanager benutzt wird
--screen=BILDSCHIRM X-Bildschirm, der verwendet werden soll
--sync X-Aufrufe synchron verarbeiten
--gtk-module=MODULE Zusätzliche GTK+-Module laden
--g-fatal-warnings Alle Warnungen als fatal betrachten
Anwendungsoptionen:
--load-type=LOAD_TYPE ROM loading method, 0 - stream from disk (like an iso), 1 - load entirely to RAM (default 0)
--load-slot=NUM Loads savestate from slot NUM
--play-movie=PATH_TO_PLAY_MOVIE Specifies a dsm format movie to play
--record-movie=PATH_TO_RECORD_MOVIE Specifies a path to a new dsm format movie
--start-paused=START_PAUSED Indicates that emulation should start paused
--cflash-image=CFLASH_IMAGE Requests cflash in gbaslot with fat image at this path
--cflash-path=CFLASH_PATH Requests cflash in gbaslot with filesystem rooted at this path
--gbaslot-rom=GBASLOT_ROM Requests this GBA rom in gbaslot
--bios-arm9=BIOS_ARM9_PATH Uses the arm9 bios provided at the specified path
--bios-arm7=BIOS_ARM7_PATH Uses the arm7 bios provided at the specified path
--bios-swi=BIOS_SWI Uses SWI from the provided bios files
--spu-mode=SPU_MODE Select SPU Synchronization Mode. 0 - Dual SPU Synch/Asynch (traditional), 1 - Synchronous (sometimes needed for streams) (default 0)
--spu-method=SPU_SYNC_METHOD Select SPU Synchronizer Method. 0 - N, 1 - Z, 2 - P (default 0)
--spu-advanced=SPU_ADVANCED Uses advanced SPU capture functions
--num-cores=NUM_CORES Override numcores detection and use this many
--scanline-filter-a=SCANLINE_FILTER_A Intensity of fadeout for scanlines filter (topleft) (default 0)
--scanline-filter-b=SCANLINE_FILTER_B Intensity of fadeout for scanlines filter (topright) (default 2)
--scanline-filter-c=SCANLINE_FILTER_C Intensity of fadeout for scanlines filter (bottomleft) (default 2)
--scanline-filter-d=SCANLINE_FILTER_D Intensity of fadeout for scanlines filter (bottomright) (default 4)
--rigorous-timing=RIGOROUS_TIMING Use some rigorous timings instead of unrealistically generous (default 0)
--advanced-timing=ADVANCED_TIMING Use advanced BUS-level timing (default 1)
--slot1=SLOT1 Device to mount in slot 1 (default retail)
--slot1-fat-dir=SLOT1_DIR Directory to scan for slot 1
--depth-threshold=DEPTHTHRESHOLD Depth comparison threshold (default 0)
--console-type=CONSOLETYPE Select console type: {fat,lite,ique,debug,dsi}
--cpu-mode ARM CPU emulation mode: 0 - interpreter, 1 - dynarec (default 1)
--jit-size ARM JIT block size: 1..100 (1 - accuracy, 100 - faster) (default 100)
--disable-sound Disables the sound emulation
--disable-limiter Disables the 60fps limiter
--nojoy=NOJOY Disables joystick support
--autodetect_method=AUTODETECT_METHOD Autodetect backup method (0 - internal, 1 - from database)
--3d-engine=ENGINE Select 3d rendering engine. Available engines:
0 = 3d disabled
1 = internal rasterizer (default)
2 = opengl
--save-type=SAVETYPE Select savetype from the following:
0 = Autodetect (default)
1 = EEPROM 4kbit
2 = EEPROM 64kbit
3 = EEPROM 512kbit
4 = FRAM 256kbit
5 = FLASH 2mbit
6 = FLASH 4mbit
--fwlang=LANG Set the language in the firmware, LANG as follows:
0 = Japanese
1 = English
2 = French
3 = German
4 = Italian
5 = Spanish
--timeout=SECONDS Quit desmume after the specified seconds for testing purpose.
--display=ANZEIGE X-Anzeige, die verwendet werden soll
Alles anzeigen
Dazu gibt es noch ein MANUAL in dem die Befehle genauer beschrieben sind.
Nun ich schätze der Befehl leutet ungefähr so:
Wäre froh um nen Tipp, lg