smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.4-1-default] (SUSE RPM) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 5K3000 Device Model: Hitachi HDS5C3020ALA632 Serial Number: ML0230FA14TNZD LU WWN Device Id: 5 000cca 36ad0459f Firmware Version: ML6OAA10 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5940 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Feb 22 00:04:30 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 28) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 372) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 134 134 054 - 100 3 Spin_Up_Time POS--- 141 141 024 - 388 (Average 391) 4 Start_Stop_Count -O--C- 100 100 000 - 3294 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 5 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 146 146 020 - 29 9 Power_On_Hours -O--C- 099 099 000 - 11689 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3216 192 Power-Off_Retract_Count -O--CK 095 095 000 - 6290 193 Load_Cycle_Count -O--C- 095 095 000 - 6290 194 Temperature_Celsius -O---- 176 176 000 - 34 (Min/Max 14/41) 196 Reallocated_Event_Count -O--CK 100 100 000 - 5 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 17155 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 17155 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 17155 [2] occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 10 0f 00 00 Error: ICRC, ABRT at LBA = 0x0000100f = 4111 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 01 00 00 00 00 10 0f 40 ff 00:19:22.791 WRITE FPDMA QUEUED 61 00 10 00 08 00 00 00 00 10 00 40 00 00:19:22.789 WRITE FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:19:22.789 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:19:22.789 SET FEATURES [Enable write cache] 61 00 10 00 00 00 00 00 00 10 0f 40 ff 00:19:22.760 WRITE FPDMA QUEUED Error 17154 [1] occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 10 0f 00 00 Error: ICRC, ABRT at LBA = 0x0000100f = 4111 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 00 00 00 00 00 10 0f 40 ff 00:19:22.760 WRITE FPDMA QUEUED 61 00 10 00 08 00 00 00 00 10 00 40 00 00:19:22.759 WRITE FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:19:22.758 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:19:22.758 SET FEATURES [Enable write cache] 61 00 10 00 00 00 00 00 00 10 0f 40 ff 00:19:22.729 WRITE FPDMA QUEUED Error 17153 [0] occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 10 0f 00 00 Error: ICRC, ABRT at LBA = 0x0000100f = 4111 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 00 00 00 00 00 10 0f 40 ff 00:19:22.729 WRITE FPDMA QUEUED 61 00 10 00 08 00 00 00 00 10 00 40 00 00:19:22.727 WRITE FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:19:22.727 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:19:22.727 SET FEATURES [Enable write cache] 61 00 10 00 00 00 00 00 00 10 0f 40 ff 00:19:22.698 WRITE FPDMA QUEUED Error 17152 [3] occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 10 0f 00 00 Error: ICRC, ABRT at LBA = 0x0000100f = 4111 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 00 00 00 00 00 10 0f 40 ff 00:19:22.698 WRITE FPDMA QUEUED 61 00 10 00 08 00 00 00 00 10 00 40 00 00:19:22.696 WRITE FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:19:22.696 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:19:22.696 SET FEATURES [Enable write cache] 61 00 10 00 00 00 00 00 00 10 0f 40 ff 00:19:22.667 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 11689 - # 2 Short offline Completed without error 00% 11682 - # 3 Short offline Completed without error 00% 11654 - # 4 Short offline Completed without error 00% 11642 - # 5 Short offline Completed without error 00% 11633 - # 6 Short offline Completed without error 00% 11625 - # 7 Short offline Completed without error 00% 11616 - # 8 Short offline Completed without error 00% 11606 - # 9 Short offline Completed without error 00% 11598 - #10 Short offline Completed without error 00% 11595 - #11 Short offline Completed without error 00% 11592 - #12 Short offline Completed without error 00% 11576 - #13 Short offline Completed without error 00% 11555 - #14 Short offline Completed without error 00% 11543 - #15 Short offline Completed without error 00% 11533 - #16 Short offline Completed without error 00% 11518 - #17 Short offline Completed without error 00% 11506 - #18 Short offline Completed without error 00% 11494 - #19 Short offline Completed without error 00% 11478 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 28/35 Celsius Lifetime Min/Max Temperature: 14/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (48) Index Estimated Time Temperature Celsius 49 2020-02-21 21:57 34 *************** ... ..(126 skipped). .. *************** 48 2020-02-22 00:04 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3216 --- Lifetime Power-On Resets 0x01 0x010 4 11689 --- Power-on Hours 0x01 0x018 6 52979909977 --- Logical Sectors Written 0x01 0x020 6 226864121 --- Number of Write Commands 0x01 0x028 6 81449508388 --- Logical Sectors Read 0x01 0x030 6 439071160 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 11391 --- Spindle Motor Power-on Hours 0x03 0x010 4 11391 --- Head Flying Hours 0x03 0x018 4 6290 --- Head Load Events 0x03 0x020 4 5 --- Number of Reallocated Logical Sectors 0x03 0x028 4 28 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 319 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 24152 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 34 --- Current Temperature 0x05 0x010 1 33 N-- Average Short Term Temperature 0x05 0x018 1 31 N-- Average Long Term Temperature 0x05 0x020 1 41 --- Highest Temperature 0x05 0x028 1 14 --- Lowest Temperature 0x05 0x030 1 38 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 36 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 106400 --- Number of Hardware Resets 0x06 0x010 4 40804 --- Number of ASR Events 0x06 0x018 4 17155 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS