Einen Schönen Abend habe das Forum schon durchsucht und bist jetzt nix gefunden .....
Habe einen kleinen HP Compaq Mini und seid neusten OpenSUSE 11.2 drauf ...
Nun meine Hilfe schrei der interne W-Lan chip funzt nicht.
habe schon mal hwinfo --netcard ausgeführt und es das ergebnis ergab sich ...
23: PCI 100.0: 0280 Network controller
[Created at pci.318]
UDI: /org/freedesktop/Hal/devices/pci_14e4_4315
Unique ID: VCu0.W63rfphOiMA
Parent ID: z8Q3.ZbAWgKMCoE3
SysFS ID: /devices/pci0000:00/0000:00:1c.0/0000:01:00.0
SysFS BusID: 0000:01:00.0
Hardware Class: network
Model: "Broadcom BCM4312 802.11b/g"
Vendor: pci 0x14e4 "Broadcom"
Device: pci 0x4315 "BCM4312 802.11b/g"
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x1508
Revision: 0x01
Driver: "b43-pci-bridge"
Driver Modules: "ssb"
Memory Range: 0xfeafc000-0xfeafffff (rw,non-prefetchable)
IRQ: 16 (896374 events)
Module Alias: "pci:v000014E4d00004315sv0000103Csd00001508bc02sc80i00"
Driver Info #0:
Driver Status: ssb is active
Driver Activation Cmd: "modprobe ssb"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #12 (PCI bridge)
24: PCI 200.0: 0200 Ethernet controller
[Created at pci.318]
UDI: /org/freedesktop/Hal/devices/pci_11ab_4354
Unique ID: rBUF.bi+3UTMsMj7
Parent ID: qTvu.bQ30eTbcr+3
SysFS ID: /devices/pci0000:00/0000:00:1c.1/0000:02:00.0
SysFS BusID: 0000:02:00.0
Hardware Class: network
Model: "Marvell 88E8040 PCI-E Fast Ethernet Controller"
Vendor: pci 0x11ab "Marvell Technology Group Ltd."
Device: pci 0x4354 "88E8040 PCI-E Fast Ethernet Controller"
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x361a
Driver: "sky2"
Driver Modules: "sky2"
Device File: eth0
Memory Range: 0xfebfc000-0xfebfffff (rw,non-prefetchable)
I/O Ports: 0xec00-0xecff (rw)
IRQ: 26 (1 event)
HW Address: 00:22:64:75:55:97
Link detected: no
Module Alias: "pci:v000011ABd00004354sv0000103Csd0000361Abc02sc00i00"
Driver Info #0:
Driver Status: sky2 is active
Driver Activation Cmd: "modprobe sky2"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #13 (PCI bridge)
46: USB 00.0: 0282 WLAN controller
[Created at usb.122]
UDI: /org/freedesktop/Hal/devices/usb_device_846_4260_00223FED4C8A_if0
Unique ID: qm0i.WetRQtdxWVE
Parent ID: cLrx.d7FDLX76qXB
SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2.1/1-2.1:1.0
SysFS BusID: 1-2.1:1.0
Hardware Class: network
Model: "NetGear NETGEAR WG111v3"
Hotplug: USB
Vendor: usb 0x0846 "NetGear, Inc."
Device: usb 0x4260 "NETGEAR WG111v3"
Revision: "2.00"
Serial ID: "00223FED4C8A"
Driver: "rtl8187"
Driver Modules: "rtl8187"
Device File: wlan0
Features: WLAN
Speed: 480 Mbps
HW Address: 00:22:3f:ed:4c:8a
Link detected: yes
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "usb:v0846p4260d0200dc00dsc00dp00icFFiscFFipFF"
Driver Info #0:
Driver Status: rtl8187 is active
Driver Activation Cmd: "modprobe rtl8187"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #42 (Hub)
Wundert euch nicht habe einen W-Lan stick angeschlossen würde aber lieber mit dem internen Arbeiten:D
Hoffe die angaben reichen ....danke jetzt schon für eure hilfe ..;)