Ich bräuchte mal wieder Hilfe!
Ich versuche auf einem alten Terra Mobile 2300 Leap 15.0 einzurichten. Vorher war XP drauf. Nach der Installation, die einwandfrei durchlief hatte ich nur eine Auflösung von 800 x 600 zur Verfügung. Was anderes kann ich auch nicht unter Systemeinstellungen - Anzeige und Monitor auswählen.
Habe dann versucht nach dieser Anleitung vorzugehen. Bei 4. fehlt mir Driver Status: xxx is active
hwinfo --gfx
21: PCI(AGP) 100.0: 0300 VGA compatible controller (VGA)
[Created at pci.378]
Unique ID: VCu0.gZLhgySda_4
Parent ID: vSkL.uvrveDpO5n6
SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:00.0
SysFS BusID: 0000:01:00.0
Hardware Class: graphics card
Model: "Silicon Integrated 771/671 PCIE VGA Display Adapter"
Vendor: pci 0x1039 "Silicon Integrated Systems Corp."
Device: pci 0x6351 "771/671 PCIE VGA Display Adapter"
SubVendor: pci 0x1558 "CLEVO/KAPOK Computer"
SubDevice: pci 0x0801
Revision: 0x10
Memory Range: 0xc0000000-0xcfffffff (ro,non-prefetchable)
Memory Range: 0xd8000000-0xd801ffff (rw,non-prefetchable)
I/O Ports: 0x9000-0x9fff (rw)
Memory Range: 0x000c0000-0x000dffff (rw,non-prefetchable,disabled)
IRQ: 9 (no events)
I/O Ports: 0x3c0-0x3df (rw)
Module Alias: "pci:v00001039d00006351sv00001558sd00000801bc03sc00i00"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #18 (PCI bridge)
Primary display adapter: #21
Alles anzeigen
xrandr ergibt:
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 640 x 480, current 640 x 480, maximum 640 x 480
default connected primary 640x480+0+0 0mm x 0mm
640x480 73.00*
lspci -nnk:
lspci -nnk
00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 671MX [1039:0671]
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: agpgart-sis
00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] AGP Port (virtual PCI-to-PCI bridge) [1039:0003]
Kernel modules: shpchp
00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] [1039:0968] (rev 01)
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 IDE Controller [1039:5513] (rev 01)
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: pata_sis
Kernel modules: pata_sis, pata_acpi, ata_generic
00:03.0 USB controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f)
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:03.1 USB controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f)
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:03.3 USB controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0 Controller [1039:7002]
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02)
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: sis190
Kernel modules: sis190
00:05.0 IDE interface [0101]: Silicon Integrated Systems [SiS] SATA Controller / IDE mode [1039:1183] (rev 03)
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: sata_sis
Kernel modules: sata_sis, pata_acpi, ata_generic
00:06.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:000a]
Kernel driver in use: pcieport
Kernel modules: shpchp
00:07.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:000a]
Kernel driver in use: pcieport
Kernel modules: shpchp
00:09.0 FLASH memory [0501]: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller [1524:0730]
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
00:09.1 SD Host controller [0805]: ENE Technology Inc ENE PCI SmartMedia / xD Card Reader Controller [1524:0750]
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: sdhci-pci
Kernel modules: sdhci_pci
00:09.3 FLASH memory [0501]: ENE Technology Inc ENE PCI Secure Digital / MMC Card Reader Controller [1524:0751]
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: sdhci-pci
Kernel modules: sdhci_pci
00:0f.0 Audio device [0403]: Silicon Integrated Systems [SiS] Azalia Audio Controller [1039:7502]
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter [1039:6351] (rev 10)
Subsystem: CLEVO/KAPOK Computer Device [1558:0801]
Alles anzeigen
Laut Datenblatt beträgt die Auflösung 1280 x 800 ( WXGA )
Habe mal diese xorg.conf erstellt. Vorlage habe ich hier gefunden. Damit bekomme ich zwar dann eine Auflösung von 1280x800 eingestellt, wenn ich aber mit dem Mauszeiger an den Rand des Bildschirms komme verschiebt sich der Bildschirminhalt vertikal und es werden Mauszeigeartefakte auf dem Rest des Bildschirms Angezeigt. Auch wenn ich auf das Anwendungsmenü gehe springt die Anzeige.
Section "Device"
Identifier "Generic Video Card"
VendorName "Silicon Integrated Systems [SiS]"
BoardName "771/671 PCIE VGA Display Adapter"
Busid "PCI:1:0:0"
Driver "vesa"
Screen 0
Option "UseFBDev" "true"
Option "DPMS"
Option "ShadowFB"
Option "MaxXFBMem"
VideoRam 262016
Option "RenderAccel" "true"
Option "AllowGLXWithComposite" "true"
Option "backingstore" "true"
Option "AddARGBGLXVisuals" "True"
EndSection
Section "Monitor"
Identifier "Configured Monitor"
Vendorname "Generic LCD Display"
Modelname "LCD Panel 1280x800"
HorizSync 31.5 - 50.0
VertRefresh 56.0 - 65.0
modeline "1280x800@60" 83.46 1280 1344 1480 1680 800 801 804 828 -hsync +vsync
Gamma 1.0
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
Defaultdepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Virtual 1280 800
Modes "1280x800@60"
EndSubSection
EndSection
Section "Module"
Load "dri"
Load "dbe" # Double-Buffering Extension
Load "v4l" # Video for Linux
Load "extmod"
Load "type1"
Load "freetype"
Load "glx" # 3D layer
Load "GLcore"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "int10"
Load "vbe"
Load "speedo"
Load "record"
Load "dri2"
EndSection
Section "DRI"
Mode 0666
EndSection
Alles anzeigen
Würde mich sehr freuen wenn mir da jemand weiterhelfen könnte! Ich hoffe ich habe alle wichtigen Informationen dazu aufgelistet.