Nach Installation von OpenSuse Leap 15.0 kann nur noch im Wiederherstellungsmodus gebootet werden

Hinweis: In dem Thema Nach Installation von OpenSuse Leap 15.0 kann nur noch im Wiederherstellungsmodus gebootet werden gibt es 33 Antworten auf 4 Seiten. Der letzte Beitrag () befindet sich auf der letzten Seite.
  • Teste mal diesen Treiber:

    Code
    zypper in xf86-video-openchrome

    Natürlich als Root...


    Nachtrag:
    Sehe gerade, dass dieser schon installiert ist )-:

    Für den Inhalt des Beitrages 123930 haftet ausdrücklich der jeweilige Autor: sterun

  • Quelle: /usr/share/doc/packages/xf86-video-openchrome/README


    Daher wären auch die Ergebnisse von:

    Code
    grep -Ei -B2 -A2 vesafb /etc/modprobe.d/50-blacklist.conf


    Code
    dmesg | grep -Ei "vesa|chrome|open|via|s3"


    Code
    grep -Ei "vesa|chrome|open|via|s3" /var/log/Xorg.0.log


    oder statt letzteren auch


    Code
    grep -E "EE|WW" /var/log/Xorg.0.log


    eventuell nicht uninteressant.

    Für den Inhalt des Beitrages 123956 haftet ausdrücklich der jeweilige Autor: tomfa-ng

  • hier erst einmal die Antworten:


    linux-81d6:~ #grep -Ei -B2 -A2 vesafb /etc/modprobe.d/50-blacklist.conf
    # list all framebuffer drivers, some of them tend to crash during boot
    # they are either compiled into the kernel, or vesafbis active
    # X works fine without them, rcfbset can load them if really required
    # sed -e '/\/drivers\/video\/.*\.\(o\|ko\)$/{s@^.*/@@;s@\..*$@@;p};d'
    linux-81d6:~ #dmesg | grep -Ei "vesa|chrome|open|via|s3"
    [ 0.000000] ACPI: RSDP 0x00000000000F78C0 000014 (v00VIAK8M)
    [ 0.000000] ACPI: RSDT 0x000000007BEF3040 00002C (v01 VIAK8M AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: FACP 0x000000007BEF30C0 000074 (v01 VIAK8M AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: DSDT 0x000000007BEF3180 005396 (v01 VIAK8M AWRDACPI 00001000 MSFT 0100000E)
    [ 0.000000] ACPI: APIC 0x000000007BEF8580 000068 (v01 VIAK8M AWRDACPI 42302E31 AWRD 00000000)
    [ 0.117195] pci 0000:00:01.0: disabling DAC on VIAPCI bridge
    [ 0.120388] pci 0000:00:10.4: VIAVLink IRQ fixup, from 5 to 11
    [ 1.748645]vesafb: mode is 1366x768x32, linelength=5504, pages=0
    [ 1.748655] vesafb: scrolling: redraw
    [ 1.748663]vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
    [ 1.748689] vesafb: framebuffer at 0xf0000000, mapped to 0xffffc90000800000, using 4160k, total 4160k
    [ 1.971513] fb0:VESAVGA frame buffer device
    [ 6.289273] sata_via0000:00:0f.0: version 2.6
    [ 6.289550] sata_via0000:00:0f.0: routed to hard irq line 11
    [ 6.329717] scsi host0: sata_via
    [ 6.366943] scsi host1: sata_via
    [ 8.126336] pata_via0000:00:0f.1: version 0.3.4
    [ 8.126556] pata_via0000:00:0f.1: VIAVLink IRQ fixup, from 255 to 10
    [ 8.162377] scsi host2: pata_via
    [ 8.194936] scsi host3: pata_via
    [ 22.294236] audit: type=1400 audit(1534689934.369:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/lessopen.sh" pid=481 comm="apparmor_parser"
    [ 23.984534] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
    [ 24.046739] via-rhine 0000:00:12.0 eth0: VIARhine II at 0xffffc900004d5000, 00:19:db:bc:e4:90, IRQ 10
    [ 24.109746] via-rhine 0000:00:12.0 eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 4de1
    [ 25.457723] snd_via82xx 0000:00:11.5: VIAVLink IRQ fixup, from 5 to 11
    linux-81d6:~ #grep -Ei "vesa|chrome|open|via|s3" /var/log/Xorg.0.log
    [ 75.907] Build Operating System: openSUSE SUSE LINUX
    [ 76.045] (**) |-->Screen "vesa" (4)
    [ 76.046] (**) | |-->Device "vesa"
    [ 76.046] (==) No monitor specified for screen "vesa".
    [ 76.201] (WW) Warning, couldn't openmodule vboxvideo
    [ 76.893] (II) LoadModule: "vesa"
    [ 76.893] (II) Loading /usr/lib64/xorg/modules/drivers/vesa_drv.so
    [ 76.902] (II) Module vesa: vendor="X.Org Foundation"
    [ 76.902] (II) VESA: driver for VESAchipsets: vesa
    [ 77.013] (EE) open/dev/dri/card0: No such file or directory
    [ 77.013] (EE) open/dev/dri/card0: No such file or directory
    [ 77.024] (II) FBDEV(0): hardware: VESAVGA (video memory: 4160kB)
    [ 77.113] (II) UnloadModule: "vesa"
    [ 77.113] (II) Unloading vesa
    [ 78.808] (II) config/udev: Adding input device (unnamed) (/dev/ttyS3)
    [ 78.809] (II) config/udev: Adding input device (unnamed) (/dev/ttyS30)
    [ 78.809] (II) config/udev: Adding input device (unnamed) (/dev/ttyS31)
    linux-81d6:~ #grep -E "EE|WW" /var/log/Xorg.0.log
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    [ 76.083] (WW) The directory "/usr/share/fonts/misc/sgi" does not exist.
    [ 76.201] (WW) Warning, couldn't open module vboxvideo
    [ 76.201] (EE) Failed to load module "vboxvideo" (module does not exist, 0)
    [ 77.013] (EE) open /dev/dri/card0: No such file or directory
    [ 77.013] (WW) Falling back to old probe method for modesetting
    [ 77.013] (EE) open /dev/dri/card0: No such file or directory
    [ 77.024] (EE) Screen 0 deleted because of no matching config section.
    [ 77.134] (EE) AIGLX: reverting to software rendering
    linux-81d6:~ #


    Ich habe mir zwar lxde installiert, ich weiß aber nicht, was das bringen soll. Wenn ich im Bootmenue den Defaultparameter wähle, stürzt der Rechner ab, ich komme gar nicht zu dem Anmeldemenue, bei dem ich lxde auswählen könnte. Es ist übrigens definitiv der Wiederherstellungsmodus, wo es dann auch funktioniert (auch Plasma) hier der entsprechende Eintrag in grub.cfg:


    menuentry 'openSUSE Leap 15.0, mit Linux 4.12.14-lp150.12.16-default (Wiederherstellungsmodus)' --hotkey=3 --class opensuse --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-4.12.14-lp150.12.16-default-recovery-8817d20a-f2bc-4d7f-9079-bfc59b0e555d' {
    load_video
    set gfxpayload=keep
    insmod gzio
    insmod part_msdos
    insmod ext2
    set root='hd0,msdos2'
    if [ x$feature_platform_search_hint = xy ]; then
    search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos2 --hint-efi=hd0,msdos2 --hint-baremetal=ahci0,msdos2 --hint='hd0,msdos2' 8817d20a-f2bc-4d7f-9079-bfc59b0e555d
    else
    search --no-floppy --fs-uuid --set=root 8817d20a-f2bc-4d7f-9079-bfc59b0e555d
    fi
    echo 'Linux 4.12.14-lp150.12.16-default wird geladen …'
    linux /boot/vmlinuz-4.12.14-lp150.12.16-default root=UUID=8817d20a-f2bc-4d7f-9079-bfc59b0e555d showopts apm=off noresume nosmp maxcpus=0 edd=off powersaved=off nohz=off highres=off processor.max_cstate=1 nomodeset x11failsafe
    echo 'Initiale Ramdisk wird geladen …'
    initrd /boot/initrd-4.12.14-lp150.12.16-default
    }


    und das ist der Eintrag, bei dem es nicht funktioniert


    menuentry 'openSUSE Leap 15.0' --class opensuse --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-8817d20a-f2bc-4d7f-9079-bfc59b0e555d' {
    load_video
    set gfxpayload=keep
    insmod gzio
    insmod part_msdos
    insmod ext2
    set root='hd0,msdos2'
    if [ x$feature_platform_search_hint = xy ]; then
    search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos2 --hint-efi=hd0,msdos2 --hint-baremetal=ahci0,msdos2 --hint='hd0,msdos2' 8817d20a-f2bc-4d7f-9079-bfc59b0e555d
    else
    search --no-floppy --fs-uuid --set=root 8817d20a-f2bc-4d7f-9079-bfc59b0e555d
    fi
    echo 'Linux 4.12.14-lp150.12.16-default wird geladen …'
    linux /boot/vmlinuz-4.12.14-lp150.12.16-default root=UUID=8817d20a-f2bc-4d7f-9079-bfc59b0e555d resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts resume=/dev/disk/by-id/ata-SAMSUNG_HD322HJ_S17AJ90SA68029-part1 splash=silent quiet showopts
    echo 'Initiale Ramdisk wird geladen …'
    initrd /boot/initrd-4.12.14-lp150.12.16-default
    }


    Ich könnte jetzt zwar mit der Brechstange rangehen und den funktionierenden Eintrag über den Defaulteintrag kopieren, aber zum einen Mal weiß ich nicht, ob es da nicht noch andere Seiteneffekte gibt und zum anderen wüsste ich auch ganz gerne, warum es nicht funktioniert.

    Für den Inhalt des Beitrages 124004 haftet ausdrücklich der jeweilige Autor: ChristianB

  • Hat er schon:

    Die Einführung der zus. Bootparameters nomodeset führt zum gleichen Ergebnis.

    Kann es sein, dass es garnichts mit der Grafik zu tun hat?
    Es muss doch ein aussagekräftiges Protokoll geben.
    Du hast geschrieben, dass der Rechner unter Leap 42.3 lief und seit Leap 15 nicht.
    Hast du ein Upgrade gemacht oder neu installiert?

    Für den Inhalt des Beitrages 124006 haftet ausdrücklich der jeweilige Autor: sterun

  • Zitat

    die zwei weiter unten funktionieren auch nicht, allerdings mit einem anderen Fehlerbild.


    Boote mal mit nem alten Kernel.......
    Und poste......…

    Für den Inhalt des Beitrages 124007 haftet ausdrücklich der jeweilige Autor: Sauerland

  • Noch ein Versuch und schnell getestet:
    Grub - auf den aktuellen (nicht funktionierenden) Eintrag
    "e" zum Editieren
    und mach aus: splash=silent quiet showopts
    ein: splash=verbose
    Speichern und starten


    PS:
    Aber Sauerland geht vor

    Für den Inhalt des Beitrages 124008 haftet ausdrücklich der jeweilige Autor: sterun

  • Versuch es mal hiermit tsc=unstable statt nomodeset

    Für den Inhalt des Beitrages 124009 haftet ausdrücklich der jeweilige Autor: Sauerland

  • Und was ist mit:

    Quelle: /usr/share/doc/packages/xf86-video-openchrome/README

    ?



    linux-81d6:~ #grep -Ei -B2 -A2 vesafb /etc/modprobe.d/50-blacklist.conf
    # list all framebuffer drivers, some of them tend to crash during boot
    # they are either compiled into the kernel, or vesafbis active
    # X works fine without them, rcfbset can load them if really required
    # sed -e '/\/drivers\/video\/.*\.\(o\|ko\)$/{s@^.*/@@;s@\..*$@@;p};d'

    Da dem nicht so ist, könntest du das mal ausprobieren.
    Auf http://www.freedesktop.org/wiki/Openchrome/ ist auch was zu deaktivierten Module wegen Abstürze zu finden.


    Mich würden ja auch die Ausgaben ausgeführt unter openSUSE Leap 42.3 interessieren.

    Für den Inhalt des Beitrages 124010 haftet ausdrücklich der jeweilige Autor: tomfa-ng