Hallo zusammen!
Seit SUSE 12.3 hab' ich ein Problem mit der WLAN-Verbindung auf meinem Notebook.
Mir scheint als ob eine Funktionstaste darauf bestehen würde mir die WLAN-Verbindung zu kappen bzw. eine Verbindung erst gar nicht zustande kommen zu lassen.
Wenn ich die Netzwerkverbindungen de- und dann wieder aktiviere erscheint im NetworkManager kurz eine Liste der verfügbaren Netzwerke; um dann ebenso schnell wieder zu verschwinden bevor ein Verbindungsversuch unternommen werden kann.
Der WLAN-Adapter scheint mir korrekt installiert (Ausgabe unten) (?!?).
Das drücken der Funktionstaste hat keine erkennbaren Auswirkungen.
Auch merkwürdig:
die Checkboxen "Netzwerkmodus aktivieren" und "Drahtlose Verbindung aktivieren" sind immer abgewählt und können auch nicht ausgewählt werden.
Im Falle von "Netzwerkmodus aktivieren" erfolgt zumindest eine Reaktion: die Netzwerkverbindungen lassen sich damit de- und aktivieren.
"Drahtlose Verbindung aktivieren" ist komplett ohne Funktion.
Hat jemand eine Idee wie man der Kiste beibringen kann, daß eine aktivierte WLAN-Karte gewünscht ist?
# uname -a
Linux artemis.rmppNETwork 3.7.10-1.1-desktop #1 SMP PREEMPT Thu Feb 28 15:06:29 UTC 2013 (82d3f21) x86_64 x86_64 x86_64 GNU/Linux
# /sbin/lspci -nnk | grep -i -A2 net
00:19.0 Ethernet controller [0200]: Intel Corporation 82577LM Gigabit Network Connection [8086:10ea] (rev 05)
Subsystem: Hewlett-Packard Company Device [103c:172a]
Kernel driver in use: e1000e
--
43:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:1508]
Kernel driver in use: b43-pci-bridge
# /usr/sbin/hwinfo --wlan
21: PCI 4300.0: 0282 WLAN controller
[Created at pci.319]
Unique ID: y9sn.YXxFBNiV6c8
Parent ID: Z7uZ.Pgi_q4KD0y3
SysFS ID: /devices/pci0000:00/0000:00:1c.3/0000:43:00.0
SysFS BusID: 0000:43:00.0
Hardware Class: network
Model: "Broadcom BCM4312 802.11b/g"
Vendor: pci 0x14e4 "Broadcom"
Device: pci 0x4315 "BCM4312 802.11b/g"
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x1508
Revision: 0x01
Driver: "b43-pci-bridge"
Driver Modules: "ssb"
Device File: wlan0
Features: WLAN
Memory Range: 0xd0500000-0xd0503fff (rw,non-prefetchable)
IRQ: 19 (no events)
HW Address: c0:cb:38:8b:83:59
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pci:v000014E4d00004315sv0000103Csd00001508bc02sc80i00"
Driver Info #0:
Driver Status: ssb is active
Driver Activation Cmd: "modprobe ssb"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #9 (PCI bridge)
Alles anzeigen
# rfkill list
1: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
2: hp-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
3: hp-wwan: Wireless WAN
Soft blocked: no
Hard blocked: no
6: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
13: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
Alles anzeigen
# dmesg | grep -i phy0
[ 12.987859] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 13.002541] b43-phy0: Found PHY: Analog 6, Type 5 (LP), Revision 1
[ 14.807633] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 14.807887] Registered led device: b43-phy0::tx
[ 14.807909] Registered led device: b43-phy0::rx
[ 14.807931] Registered led device: b43-phy0::radio
[ 18.400987] b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
[ 24.770085] b43-phy0: Radio hardware status changed to DISABLED
[ 438.820150] b43-phy0: Radio hardware status changed to ENABLED
[ 438.977825] b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
[ 443.792509] b43-phy0: Radio hardware status changed to DISABLED
[ 1804.395253] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 1804.409723] b43-phy0: Found PHY: Analog 6, Type 5 (LP), Revision 1
[ 1804.417190] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 1804.417600] Registered led device: b43-phy0::tx
[ 1804.417652] Registered led device: b43-phy0::rx
[ 1804.417714] Registered led device: b43-phy0::radio
[ 1804.615327] b43-phy0: Loading firmware version 508.154 (2009-08-18 00:58:22)
[ 1804.708222] b43-phy0: Radio hardware status changed to DISABLED
[ 1804.708409] b43-phy0: Radio turned on by software
[ 1804.708414] b43-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.
Alles anzeigen